6 Inch Stovepipe: 22 gauge single-wall
by HeatFab Saf-T Pipe |
|
The highest quality single-wall stove pipe available
for coal and wood-burning stoves, fireplaces and central heaters.
Unmatched in safety, durability and ease of installation.Made
with 22-gauge cold-rolled steel, practically 60% thicker than
standard single wall stove pipes.
An invisible seam finishes each connector piece
with a high-quality silicone-based black stove paint. Continuous-seam
laser welding creates stovepipe you can depend on to fit consistently
– because it’s consistently round.
Saf-T Pipe retains its factory-round shape, even
when cut. Because this pipe doesn’t have to be snapped together,
it’s quicker to install – and it can’t come apart,
even in case of fire (especially in the case of fire). Joints
fit perfectly to ensure tight, safe venting and eliminate the
release of soot and flue gas to interior environments.
- Laser-welded seams
- Will last
longer than standard 24 gauge pipe
- Inside of each piece painted to prevent flash rust.
- Beaded for furnace cement
- High-temperature, low-luster finish
|
|
|
|
| |
12" Straight
Pipe
Use for a single-wall connector pipe. Requires 18” clearance
to combustibles. |
|
|
| |
|
18" Straight Pipe
Use for a single-wall connector pipe. Requires 18”
clearance to combustibles. |
|
| |
|
24" Straight Pipe
Use for a single-wall connector pipe. Requires 18” clearance
to combustibles. |
|
|
| |
|
36" Straight Pipe
Use for a single-wall connector pipe. Requires 18”
clearance to combustibles. |
|
| |
|
45 Degree Elbow
Offsets obstructions as needed. Non-adjustable.. |
|
|
| |
|
48" Straight Pipe
(Case of 4)
Use for a single-wall connector pipe. Requires 18”
clearance to combustibles. |
|
6" x 48" |
Ocp21130 |
$322.99 |
|
|
|
90 Degree Elbow
Offsets obstructions as needed. Non-adjustable. Not recommended
for rear exit appliances. |
|
|
| |
|
Adjustable Elbow
90° sectioned. Double seams permit each section
to turn freely without any danger of becoming disconnected.
Can quickly be adjusted to any straight line and a right angle. |
|
| |
|
Slip Connector
18" length. Use to adapt pipe to ceiling support box
or finishing collar. Adds 4” - 16” of length to
rigid pipe. Allows drip-free installation without cutting
the pipe. Can be used in line to create a telescoping combination
when used with a straight length of pipe. |
|
|
| |
|
Tee Cap
Used to close off one end of a stove pipe tee. Use
of a tee cap allows for easy access for pipe cleaning. |
|
| |
|
Tee Connector
Provides a connection between Heat-Fab 22-ga. Black Stovepipe
and a tee with a female take-off. 12" long and has two
male ends |
|
|
| |
|
Tee Joint
Both sections assembled with "Snaplock" seam. Can
be easily turned to make a secure lock. |
|
| |
|
Telescoping Length
Use for a two-piece installation. Connects directly from stove
to ceiling support box or finishing collar. Adjusts from 38"-70".
No cutting required. |
|
|
6" x 38" - 70" |
Ocp21135 |
$114.99 |
|
|
|
Trim Collar
Covers excess area around flue opening. Provides
a finished look to stove pipe installation. |
|
| |
|
